|
|
Audio pre-amplifier for two satellites and subwoofer
Štaud, Stanislav ; Brančík, Lubomír (referee) ; Kratochvíl, Tomáš (advisor)
The aim of this thesis was to design, simulate and construction audio pre-amplifier for two satellites and subwoofer and monolithic amplifier for subwoofer in the class AB. Audio pre-amplifier provides bass, treble and switch loudness volume control. It includes subsonic filter and active crossovers Sallen-Key with approximation Linkwitz-Riley. There are low noise operating amplifiers LM833 and TL081 at the place of active amplifiers with very low distortion. End-amplifier can delivers power 50 W to 4 ohms. Of consists delayed switch speaker and supports security against direct voltage on the output of amplifier.
|
|
|
Class AB audio amplifier for two satellites and subwoofer
Cupák, Jan ; Brančík, Lubomír (referee) ; Kratochvíl, Tomáš (advisor)
This bachelor’s thesis deals with design of AB class audio amplifiers. Further more it deals also with other functional blocks, e.g. preamplifier, tone equalizer and active crossover. Outcome of this work is a complete solution of the amplifier with it's simulation. In final solution is also included scheme of a high quality power supply unit, speaker protection and heat sinks for high performance transistors. In this project is also included a solution of task about optimal mechanical arrangement of the single parts in the case of this amplifier. This thesis contains results of measurement and photo document of functional prototype.
|
|
|
Amplifier for subwoofer with output power 100 W
Chevalier, Stanislav ; Petržela, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
This project is focused on design of the power amplifier for subwoofer, its circuit’s protection, speaker’s protection and design of the filter for subwoofer. The amplifier is operating in AB class and its power is up to 100 W/ 4 ohms. It is made of discrete electronics components and devices. The protections of the amplifier are against short circuit in output, the speaker pops when turned on and against the DC voltage at the amplifier’s output. Filter for subwoofer contains combiner at the input, volume control, subsonic filter, low-pass filter with adjustable cut-off frequency and output amplifier with possibility of phase changing of the output signal.
|
|
| |
|
|
Design of class AB stereo audio power amplifier
Zatloukal, Tomáš ; Polák, Ladislav (referee) ; Brančík, Lubomír (advisor)
The following work deals with design of class AB low-frequency amplifier, which is appropriately supplemented by correction Pre-amplifier and inrush protection circuit. The original schematic from prof. Leach was edited to fulfill task and to be easily completed from discrete components. The result of this work is the final design of power amplifier and correction pre-amplifier, protection circuit for speakers and power supply. As a next part, the design of printed circuit boards will be described together with assembling and mounting of boards in a construction box. Power amplifier will be verified by simulation and hardware measurements.
|
|
|
Simulation and implementation of the audio power amplifier
Svadbík, Pavel ; Kratochvíl, Tomáš (referee) ; Šotner, Roman (advisor)
This work deals with simulation and analysis of audio power amplifiers of various concepts and classes. The theoretical part presents the basic necessary knowledge of electrical concepts and principles necessary for mastery of issues that this work deals. For each simulated circuit are described the basic operating principles and evaluated the results of the analysis. Based on the results of the analysis is chosen circuit, which is experimentally realized and measurement. In conclusion discusses the parameters obtained by simulations and practical measurements, and are fully assessed characteristics realized amplifier.
|
|
|
Stereo equalizer with spectrum analyzer
Náhlík, Ondřej ; Šotner, Roman (referee) ; Kratochvíl, Tomáš (advisor)
This bachelor’s work is focused on design of ten band analog stereo equalizer, which is solved by using an active band-pass filters of 2nd order. Simulated output signal isn‘t rippled more than ± 1 dB at zero amplification and can be amplified at maximum ca. ± 8 dB. Prototype of equalizer is then built and it’s characteristics are measured. The circuit of an integrated power amplifier working in the class AB is solved in the next part of this work. Amplifier is then built and it’s characteristics are measured. In the last part of this work, there is described function of a spectral analyzer which is then designed, built and programmed. The analyzer uses the Fast Fourier transform (FFT) and resulting spectrum is displayed on a display.
|
|
|
Class-AB stereo audio power amplifier
Chmelík, Šimon ; Šotner, Roman (referee) ; Brančík, Lubomír (advisor)
This bachelor thesis deals with design of low-frequency power amplifier working in AB class, including correction preamplifier and a suitable power source. The amplifier is designed to be feasible from commonly available components. The result is the overall design of power amplifier with preamplifier and power supply and measuring their parameters.
|
|
|
Class D audio amplifier for active loudspeakers
Cupák, Jan ; Punčochář, Josef (referee) ; Kratochvíl, Tomáš (advisor)
This master's thesis deals with design of D class audio final amplifier, which was output power 400 W for 4 ? load impedance. Designed audio amplifier is specifical for active speaker, which consists of satelite speakers and subwoofer. Further more it deals also with other functional blocks, e.g. balanced input preamplifier, active crossover and protection for safety running. Outcome of this work are schemes of each functional blocks of D class audio amplifier, whose functionality was verified by simulation. Thesis also contains full reference material including mechanical arrangement of functional blocks on printed connection board. The conclusion contains the measured parameters of function blocks of produced prototype and complete photographic documentation.
|
|
| |
guest ::
